Metered Chemical Injection
Storage tank, metering pump and injection quill form the core of a controlled H₂S scavenger dosing system.
EXPLORAX • PRODUCTION CHEMISTRY
H2S-60
60% MEA TRIAZINE H₂S SCAVENGER
60% MEA TRIAZINE H₂S SCAVENGER
High-active monoethanolamine-based triazine scavenger for oil & gas H₂S treatment systems. H2S-60 is positioned as a concentrated commercial grade where customers want higher delivered active content with practical liquid handling and pumpability.
High-active treatment chemistry
MORE ACTIVE. LESS CARRIER.
EXPLORAX H2S-60 is a water-based MEA-triazine solution designed for customers who prefer a higher-active commercial grade. Compared with lower-active versions, the 60% format delivers more active scavenger per unit volume while retaining a workable liquid viscosity profile for storage, transfer and metered injection.
Water-based liquid
Clear to pale-yellow liquid with mild amine odour and full water solubility.
Commercial high-active positioning
Useful where transport efficiency and active concentration per package matter.
Controlled injection
Designed for metering into gas or production-treatment systems where dosage is established by system demand.
Qualification required
Final dosage depends on inlet H₂S, flow, pressure, contact conditions and treatment target.
TREATMENT VISUALS
FROM INJECTION
TO TREATED STREAM.
MEA-Triazine Contact & Reaction
Sour stream contacts triazine chemistry and exits with reduced H₂S concentration.
Production Treatment Point
Scavenger injection can be integrated around separators, gas outlets and downstream process equipment.
Current specification
H2S-60
TECHNICAL DATA.
The values below are taken directly from the current parameter sheet supplied for MEA Triazine 60 Grade.
01
Chemical type
Monoethanolamine-based triazine
IDENTITY
02
Active ingredient formula
C9H21N3O3
CHEMICAL FORMULA
03
Molecular weight of active
219.28
g/mol
04
Appearance
Clear to pale yellow liquid
PHYSICAL
05
Odour
Mild amine
PHYSICAL
06
Active content / target range
59.5–60.5
wt.%
07
Calculation active basis
60.0
wt.%
08
Carrier
Water-based
COMPOSITION
09
Colour
≤60 (target)
APHA
10
pH, neat @ 25°C
9~11
pH
11
Calculated density @ 25°C
1.153
g/mL
12
Calculated specific gravity
1.157
25/25°C
13
Dynamic viscosity @ 25°C
12.53
cP (mPa·s)
14
Free MEA — dilution estimate
0.83
wt.%
15
Free MEA — requested / source limit
<1%
wt.%
16
Methanol
<1%
wt.%
17
Water solubility
Completely miscible
SOLUBILITY
18
Free formaldehyde — dilution estimate
0.23
wt.%
19
Free formaldehyde — source limit
<1%
wt.%
TREATMENT LOGIC
CONTACT.
REACT.
VERIFY.
The internal page should communicate H₂S scavenging as a controlled treatment sequence rather than a single generic claim. In practice, the required dose and contact conditions depend on the actual sour stream and operating target.
Typical injection concept
The scavenger is metered into the sour gas or process stream, mixed with the stream, allowed to contact and react, and followed by verification of the treated outlet. The attached process graphic is presented as an application illustration rather than a fixed engineering design.
01
Detect
Establish inlet H₂S concentration and treatment target.
02
Inject
Meter H2S-50 at a controlled injection point suited to the process.
03
Contact
Provide adequate mixing and residence time for the scavenging reaction.
04
Verify
Measure downstream H₂S and optimize dosage against actual performance.
APPLICATION DIRECTIONS
WHERE H2S-60
CAN BE EVALUATED.
Sour Gas Treatment
Continuous or staged scavenger injection into sour gas streams where a liquid MEA-triazine treatment route is appropriate.
Separator / Production Gas
Injection around separator gas outlets or downstream production-treatment equipment to reduce H₂S before further handling.
Crude / Liquid Systems
Can be evaluated in selected hydrocarbon or process liquid applications where H₂S control is required and compatibility is confirmed.
Storage & Transfer
Useful as a treatment concept for tanks, transfer systems and process lines when H₂S control is required during handling.
Pipeline Injection
Metered injection can be considered where mixing and contact time in the line support the intended treatment objective.
Field Qualification
Dosage should be optimized using actual inlet H₂S, flow, temperature, pressure and downstream target values.
PACKAGING & LOGISTICS
FLEXIBLE GRADE.
PRACTICAL SUPPLY.
The 50% grade is positioned as a balanced mid-active supply format. It delivers more active chemistry per package than H2S-40 while retaining greater carrier content than the 60% and 80% grades. Final pack size and shipment configuration should follow the approved commercial specification.
Packaging
IBC / drum / bulk options to be confirmed against the current commercial pack specification.
Transport efficiency
Higher active content means less carrier water is shipped per unit of active chemistry than with 40% or 50% versions.
Handling
20–40 cP viscosity at 25°C supports practical liquid transfer and metering.
Storage
Final storage temperature and shelf-life statements should be added from the approved TDS / MSDS.
TECHNICAL QUESTIONS
FAQ.
This sample uses only supported product specifications and keeps dosage/performance claims application-dependent until field or lab data are supplied.
The current parameter sheet specifies 59.5–60.5 wt.% active content.
The current parameter sheet specifies a dynamic viscosity of 20–40 cP at 25°C.
Yes. The supplied parameter sheet describes the grade as water-soluble.
Clear to pale-yellow liquid with mild amine odour.
The current parameter sheet gives pH 9–11 at 25°C.
A fixed dosage is not stated in the supplied parameter sheet. Dosage should be established using inlet H₂S, flow, contact conditions and the required outlet target.
It can be presented as a metered-injection treatment concept, but the exact injection design must be qualified for the actual process.
Calculated density is 1.132 g/mL at 25°C.
Calculated specific gravity is 1.135 at 25°C/25°C.
Not in the supplied parameter sheet. Shelf life should be added only from the approved current TDS or commercial specification.
NEED H₂S-60 FOR YOUR STREAM?
Share inlet H₂S, flow, pressure, temperature, gas/liquid phase and outlet target. That information is needed to design a meaningful qualification program.
START A TECHNICAL DISCUSSION ↗